cree xb-d color series features a pplications > cree's smallest lighting class led: 2.45 x 2.45 mm > non-directional > 1a maximum drive current > directional > wide viewing angle: 115(white) to 140 (red) > downlight > electrically neutral thermal path > consumer portable flux characteristics @ 85c color dwl (nm) kit used blue 465-485 0z01 green 520-535 0b01 red-orange 610-620 o 901 red 620-630 o 701 characteristics unit minimum typical maximum thermal resistance, junction to solder point - white, royal blue, blue c/w 6.5 thermal resistance, junction to solder point - green c/w 11 thermal resistance, junction to solder point - amber c/w 7 thermal resistance, junction to solder point - red-orange, red c/w 5 viewing angle (fwhm) - white degrees 115 viewing angle (fwhm) - royal blue, blue, green degrees 135 viewing angle (fwhm) - amber, red-orange, red degrees 140 temperature coefficient of voltage - white mv/c -2.5 temperature coefficient of voltage - royal blue, blue, green mv/c -3.3 temperature coefficient of voltage - amber, red-orange, red mv/c -2 esd classification (hbm per mil-std-883d) class 2 dc forward current ma 1000 reverse voltage v -5 forward voltage (@ 350 ma, 85 c) - white v 2.9 3.5 forward voltage (@ 350 ma, 25 c) - royal blue, blue v 3.1 3.7 forward voltage (@ 350 ma, 25 c) - green v 3.3 3.9 forward voltage (@ 350 ma, 25 c) - amber, red-orange, red v 2.25 2.6 led junction temperature c 150 it is highly recommended for the user to review the cree xbd series page for additional and most recent technical data at: http://www.cree.com/led-components-and-modules/products/xlamp/discrete-directional/xlamp-xbd cree xlamp xb-d color leds extend the double lumens-per-dollar performance of the xb package to color leds, delivering up to 40% higher maximum light output than xp-e color leds. the combination of performance and small size of xb-d color leds enable better color mixing and lower system cost. 80.6 67.2 cree xb-d color series on board min.flux (lm) @350ma 35.2 93.9 global headquarters, 3 northway lane north, latham, ny 12110, usa www.marktechopto.com toll free: 1-800-984-5337 ? phone: 518-956-2980 ? fax: 518-785-4725 ? email: info@marktechopto.com
hardware (not included) > mount with #4 machine screws. > 16awg maximum wire gauge. > use only with constant current power supplies. pcb fabrication > layer count: 1 > core material: 6061-t6 aluminum > single layer copper weight: 1oz > solder mask: white > finishing plating: pb free hasl * exceeding maximum ratings may damage the led and cause potential safety hazards. * elevated operating temperatures can be expected to negatively impact the service life (lumen output) * all data is related to entire assembly. data reflects statistical mean values. actual data may differ depending on variances in the manufacturing process. * end users need to take into account the lumen depreciation as the temperature rises with various thermal solutions installed. note 1: using continuously under elevated loads (i.e. the application of high temperature/current/voltage or a significant change in temperature, etc.) may cause this product to significantly decrease in reliability even if the operating conditions are within the absolute maximum ratings. note 2: the thermal resistance from the led junction to ambient temperature, rth(j-a), should be kept below 10c/w so that the led is not exposed to a condition beyond the absolute maximum ratings. note 3: the temperature of the led assembly must be measured at the tc-point according to en60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. cree xb-d color series on board global headquarters, 3 northway lane north, latham, ny 12110, usa www.marktechopto.com toll free: 1-800-984-5337 ? phone: 518-956-2980 ? fax: 518-785-4725 ? email: info@marktechopto.com
|
